Walk into any hardware store and you’ll find bags labeled Type N and Type S, and maybe Type M. Online advice usually ends with “use Type S, it’s stronger.” For a modern block wall that might be fine. For a pre-1950 brick or limestone building, “stronger” is usually exactly the wrong goal. Here’s how the mortar types work, and how to pick the right one for an old wall.
What are the mortar types?
Modern mortars are classified under ASTM C270, the U.S. standard for masonry mortar. The types are named from a skipped-letter sequence in the phrase MaSoN wOrK, which is an easy way to remember them in order from strongest to weakest:
| Type | Typical proportions (cement : lime : sand) | Min. compressive strength | Typical use |
| M | 1 : ¼ : 3 | 2,500 psi | Foundations, retaining walls, heavy loads |
| S | 1 : ½ : 4½ | 1,800 psi | Below grade, high wind or lateral loads, pavers |
| N | 1 : 1 : 6 | 750 psi | General above-grade modern walls |
| O | 1 : 2 : 9 | 350 psi | Non-load-bearing, protected walls, historic repointing |
| K | 1 : 3 : 12 | ~75 psi | Very soft historic masonry |
Read the proportions column and the pattern is obvious. As you move down the list, the Portland cement drops and the lime rises. Less cement means softer, more flexible, and more vapor-permeable mortar. More cement means harder, stiffer, and less breathable.
Type N vs. Type S: what’s the actual difference?
Type S has roughly half the lime of Type N relative to cement. It reaches more than twice the compressive strength and has better bond strength. That makes it the right call for retaining walls, below-grade block, and structures that take lateral loads.
Type N is the general-purpose choice for modern above-grade brick veneer. It’s balanced, workable, and forgiving.
For a wall built before 1950, both are usually too hard. Most historic Chicago brick, and especially the soft salmon-colored common brick on side and rear walls, is weaker than a cured Type S joint, and often weaker than Type N. Put a mortar stronger than the brick into that wall and the brick becomes the sacrificial element instead of the joint. We explain the mechanism in Lime Mortar vs. Portland Cement.
What is Type O mortar used for?
Type O is the low-strength, high-lime member of the family. In new construction it’s limited to non-load-bearing and protected work. In restoration it plays a different role: it’s one of the most common starting points for repointing historic brick, because its strength and stiffness sit close to many period mortars. On older or softer walls we go softer still, with Type K proportions or pure lime mortars.
What about lime mortar?
Before about the 1880s, Chicago walls were laid in lime and sand with no Portland cement at all. By the 1920s and 1930s, many mixes included some Portland. Restoration lime mortars come in two families:
- Non-hydraulic lime (lime putty): cures slowly by absorbing carbon dioxide from the air. It’s the softest and most breathable option and the closest match to the earliest walls.
- Natural hydraulic lime (NHL 2, NHL 3.5, NHL 5): sets partly with water, so it cures faster and handles exposure better, while staying far more breathable than cement mortars. The number indicates relative strength.
The right choice comes from analyzing your building’s original mortar, not from a default. The National Park Service’s Preservation Brief 2 states the principle plainly: new mortar should match the historic mortar and be softer than the masonry units around it.
Which mortar for which part of a Chicago building?
- Common brick side and rear walls: soft lime-rich mixes, typically Type O, Type K, or lime. This brick has the least margin for error in the city.
- Pressed face brick on street facades: harder and denser than common brick, but usually still laid in lime-rich mortar. It’s matched to the original, not upgraded.
- Greystone limestone fronts: Indiana (Salem/Bedford) limestone over common brick backing. That’s two materials and often two mortars on one building, which is why greystone restoration chicago projects can’t use one bag mix for everything.
- Old limestone and dolomite foundations: many pre-1890 Chicago foundations are Joliet-Lemont dolomite laid in lime. They’re constantly damp, and owners are often told to “upgrade” to Type S. Doing that traps water in the stone and speeds up its layered spalling. Proper limestone foundation repair keeps the joints breathable so moisture leaves through the mortar, not the stone.
- Parapets, chimneys, copings: the most exposed parts of any building. A mason may step up slightly, for example to a stronger NHL, but never past the strength of the brick.
What happens when the wrong mortar is already in the wall?
If a previous contractor repointed with Type N or S, or with straight cement, the damage shows up in a predictable pattern. Brick faces flake next to proud gray joints, typically on gangway and rear walls first. The fix is to carefully remove the hard mortar, which is slow work since it’s often harder than the brick around it, and repoint in a compatible mix. Where brick has already been lost, chicago common brick replacement with salvaged units keeps the repair invisible. If you’re seeing flaking already, read Why Is My Brick Flaking? first.
Frequently asked questions
Is Type S better than Type N?
It’s stronger, not better. Type S belongs below grade and in walls that take lateral loads. For historic brick, extra strength becomes a liability, because the mortar should always be the weaker element.
Can I repoint old brick with Type N mortar?
On some 1930s–40s face brick with Portland-based original mortar, a Type N-range match may be appropriate. On anything older, or on common brick, it’s usually too hard. The original mortar, not the bag at the store, should decide.
How can I tell if my building has lime mortar?
Lime mortar is usually lighter in color, softer, and can often be scratched with a key or a screwdriver. Hard gray mortar that resists a steel point is likely Portland-based, and if it was used for repointing an older wall, it may be causing damage. A lab or field analysis confirms the composition.
Does mortar type affect how long repointing lasts?
Yes, but not the way most people expect. A correctly matched soft mortar wears slowly and protects the brick, which is the outcome you want. See What Is Tuckpointing? Repointing Brick Explained for what a durable repointing job involves.
Sources & further reading: National Park Service, Preservation Brief 2 – Repointing Mortar Joints in Historic Masonry Buildings · National Park Service, Preservation Briefs library · ASTM C270, Standard Specification for Mortar for Unit Masonry
Not sure what’s in your joints, or what should be? We start every project by analyzing the original mortar and matching it. Learn more about our brick mortar repair and stone mortar repair services, or get in touch for a free assessment.

