What Is Tuckpointing? Repointing Brick Explained for Owners of Old Buildings

Ask five Chicago contractors what tuckpointing is and you’ll get five answers, and most of them will be describing something else. The word has drifted so far from its original meaning that owners often pay for one thing and get another. Here’s what tuckpointing actually is, what repointing brick means, and why the difference matters for any building put up before 1950.

What is tuckpointing, technically?

Tuckpointing started as a decorative technique in 18th- and 19th-century England. Masons filled the joints of an uneven brick wall with mortar tinted to match the brick. Then they cut a thin groove down the center of each joint and “tucked” in a narrow ribbon of contrasting lime putty, usually white. From across the street, the wall looked like it was built of perfectly crisp, precise brick, even when it wasn’t.

True tuckpointing is rare today and is mostly done as a restoration specialty on buildings that originally had it. When most people in Chicago say “tuckpointing,” they mean something else.

So what are Chicago contractors actually selling?

In everyday American usage, “tuckpointing” means repointing: grinding or raking out deteriorated mortar from the joints and packing in new mortar. That’s the job almost every “tuckpointing” quote describes. We break down the terminology in more detail in our guide to tuckpointing vs repointing. The short version is that the name on the quote matters far less than what goes into the joint.

What does repointing brick involve, done properly?

On a pre-1950 wall, correct repointing follows a sequence. Most of the steps aren’t visible once the job is done.

  • Mortar analysis first. A sample of the original mortar tells us its approximate composition, hardness, sand color, and grain. A 1895 cottage and a 1928 bungalow carry very different mortars, and the repair has to match the one actually in your wall.
  • Careful removal. Old mortar is raked out to a depth of roughly 2 to 2.5 times the joint width, enough for the new mortar to key in properly. On soft brick this is often done with hand tools, because an angle grinder can widen joints and chip brick edges in seconds.
  • A matched mix. The new mortar has to be softer and more breathable than the brick. That usually means a lime-rich mix or pure lime mortar, never a bag of high-strength cement mix. Our Lime Mortar vs. Portland Cement guide explains why that one rule decides whether a repair lasts a century or ruins the brick in a decade.
  • Filling in layers. Deep joints are filled in thin lifts, each allowed to firm up before the next, so the mortar cures without voids or shrinkage cracks.
  • Matching the joint profile. Concave, flush, raked, struck, or beaded: the finished joint should match the original tooling so the repair disappears into the wall.
  • Curing. Lime mortar needs to stay damp and protected from sun, wind, and frost while it cures. Rushing this stage is one of the most common reasons repointing fails early.

The National Park Service’s Preservation Brief 2: Repointing Mortar Joints in Historic Masonry Buildings remains the standard reference for this process. It’s also what the Commission on Chicago Landmarks expects to see followed.

Why does the mortar have to be softer than the brick?

Because in a historic wall, the mortar is the sacrificial part. Soft lime joints flex with movement and let moisture escape. Over decades they wear back slowly while the brick stays intact. When the joints wear out, you repoint, which is a routine maintenance task.

Reverse that relationship with hard Portland cement and the wall starts working against itself. Moisture can’t get out through the joints, so it leaves through the brick face. Every freeze-thaw cycle then pushes the face off. That’s the mechanism behind most of the flaking we see, covered in Why Is My Brick Flaking? Spalling Explained. New mortar can be removed and redone. A spalled brick has to be replaced.

How long does repointing last?

It depends on the exposure, the mix, and the workmanship. Well-matched lime repointing on a sheltered wall commonly lasts several decades. Parapets, chimneys, and copings take more weather and wear faster. We give realistic numbers by wall location in our answer to how long does tuckpointing last, along with the warning signs that a “cheap” job won’t make it to its first decade.

How do I know if my wall needs repointing?

A quick check you can do yourself, with the urgency rising down the list:

  • Joints recessed a quarter inch or more, sandy mortar that crumbles under a key, or hairline gaps between brick and mortar. These are the normal signs of age. Plan the work within a season or two.
  • Open joints at parapets, chimneys, and under sills, or white efflorescence bands. Water is getting in at the top or behind the face. Get an assessment before the next winter.
  • Flaking brick next to hard gray joints, loose bricks, cracks running through brick rather than along joints, or bulging areas. This is no longer just a mortar problem. Have it looked at now.

If your building is landmarked or inside a landmark district, exterior repointing also needs review before a permit is issued. See Do You Need a Permit to Tuckpoint a Landmark Building in Chicago?

When is repointing part of a bigger restoration?

Sometimes the joints are only the visible symptom. Rotted lintels, failed copings, displaced brick, or earlier cement repairs that have already damaged the face mean the job grows from repointing into historic brick restoration. That can include replacing spalled units with salvaged brick, rebuilding parapets, and correcting water details. A good assessment tells you honestly which situation you’re in, and doesn’t sell you the bigger one if you don’t need it.

Frequently asked questions

Is tuckpointing the same as repointing?

In everyday Chicago usage, yes. Both words describe replacing deteriorated mortar. Technically, tuckpointing is a decorative finish with a contrasting ribbon joint, and repointing is the repair. What matters on your quote is the mortar specification and the removal method, not the label.

Can I just fill the cracks myself?

Small, isolated areas on a low wall can be a reasonable DIY project if you use a compatible lime mix and rake the joint out properly first. Smearing caulk or cement over the surface of a joint traps water and makes the eventual repair harder. Anything above a ladder’s reach, around a chimney, or on a parapet is a job for a mason.

Will new mortar match the old color?

It should. Color comes mostly from the sand and the binder, not from added pigment, so matching starts with the mortar analysis. Expect fresh lime mortar to look slightly lighter for the first months while it cures and weathers in.

Do I need to repoint the whole building at once?

Rarely. Most buildings fail first at parapets, chimneys, gangway walls, and below sills. Repointing those areas first, then the remaining walls as needed, is often the most cost-effective approach. See How Much Does Tuckpointing Cost in Chicago? for how scope affects price.

Sources & further reading: National Park Service, Preservation Brief 2 – Repointing Mortar Joints in Historic Masonry Buildings · National Park Service, Preservation Briefs library · City of Chicago, Landmarks permit review

Not sure whether your wall needs repointing, a few spot repairs, or nothing yet? Send us a few photos and we’ll tell you honestly. Learn more about our brick mortar repair service, see finished work in our gallery, or get in touch for a free assessment.

Let's Stay in Touch
Phone
Address
2211 N Elston Ave, Chicago, IL 60614
Open Hours
Monday - Friday: 9AM – 5 PM

Copyright © 2025 | All Rights Reserved